www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 110 l s3 m arking ? hdf112 prepared checked approved ? d a t e 200 6 - 5 - 11 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . modi fy content ? remark
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 8 1. scope this specification shall cover the characteristi c s of saw filter f110 l . 2. electrical specification dc voltage vdc 10v ac voltage vpp 10v50hz/60hz operation temperature - 4 0 to + 8 5 storage temperature - 45 to +85 rf power dissipation 0 dbm 2.2 electronic characteristics ? part number hdf110 l ? (fo)(mhz) nominal center frequency 110 3db bandwidth(from fo)(khz) +/ - 576min ? stop band attenuation (from peak level)(db) 1)fo - 3 1.728 mhz 2)fo - 2 1.728 mhz 3)fo+/ - 1.728mhz 4)fo+2 1.728mhz 5)fo+3 1.728mhz 50min 45min 30min 40min 40min (db) insertion loss(at minimum loss point) 4.5max ?? ( fo+/ - 576khz)( sce.) group delay deviation 0.7 / input/output impedance 300 //1.2 h
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 8 typical frequency response 3. dimensi on marking hdf 112 hd: brand f : filter 112 : no. 3.input 2. input ground 1.5. to be ground 6.output ground 4.8. case ground 7. output
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 8 4.test circuit 5. environmental characteristics 5 - 1 high temperature exposure subject the device to +85 for 16 hours. then release the filter into th e room conditions for 24 hours prior to the measurement. it shall fulfi ll the specifications in 2.2 . 5 - 2 low temperature exposure subject the device to - 4 0 for 16 hours. then release the device into the room conditions for 24 hours prio r to the measure ment. it shall fulfill the specifications in 2.2 . 5 - 3 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +8 5 for 30 minutes. then release the device into the room conditions for 24 hou rs prior to the me a surement. it shall meet the specifications in 2.2 . 5 - 4 resistance to solder heat dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for 10 1 sec. then release the device into the room conditions for 4 hours . the device shall meet the specifications in 2.2 . 5 - 5 solderability subject the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the terminals must be covered with new solder. it shall me et the specifications in 2.2 . 5 - 6 mechanical shock drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulf ill the specifications in 2.2 . 5 - 7 vibration subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the device shall fulfill the specifications in 2.2 .
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 8 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structur e (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 8 quantity lot no. (3) leader part and vacant position specifications. 8. tape specifications 8.1 ten sile strength of carrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions
saw filter hdf 110 l s3 www.s houlder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 8 [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 8.0 0.1 2.0 0.05 ? 1.5 0.1 ? 1.0 0.25 0.3 0.05 2.10 0.1 6.40 0.1 5.20 0.1 [figure 2] [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
